 |
 |
T.P.271-T.R.276
PLATE O/DIAMETER mm (inch) - 270 (10.63')
ANGULAR INDEXING ACCURACY T.P.271/T.R.276 - �60''/30''
PLATE DRIVING TORQUE AT 6 bar (87 P.S.I.) - 50 Nm (37 ft.lb)
WEIGHT Kgs (lbs) - 33 (72) |
|
|
 |
T.R.278
PLATE O/DIAMETER mm (inch) - 305 (12.01')
ANGULAR INDEXING ACCURACY - � 30'
PLATE LOCKING FORCE AT 6 bar (87 P.S.I.) - 4400 N (971 lbs)
WEIGHT Kgs (lbs) - 34 (75)
|
|
|
 |
T.RI.320-315
PLATE O/DIAMETER mm (inch) - 320 (12.60'')
ANGULAR INDEXING ACCURACY - � 10''
PLATE LOCKING FORCE AT 30 bar (435 P.S.I.) - 18000 N (3968 lbs)
WEIGHT Kgs (lbs)- 85 (187)
|
|
|
 |
F.P10.75 - F.P10.150
TOTAL STROKE mm (inch) F.P10.75 - 75 (2.95'')
DRILLING CAPACITY mm (inch) F.P10.75- MILD STEEL - 10 (0.39'')
PNEUMATIC THRUST N (lbs)6 bar (87 P.S.I.) F.P10.75- 1350 (302)
WEIGHT F.P10.75- Kgs (lbs)- 18 (39)
|
|
|
 |
F.P14.100
TOTAL STROKE mm (inch) F.P14.100 - 100 (3.94'')
DRILLING CAPACITY mm(inch) F.P14.100- MILD STEEL - 14 (0.55'')
PNEUMATIC THRUST N (lbs) 6 bar (87 P.S.I.) F.P14.100- 2450 (548)
WEIGHT F.P14.100- Kgs (lbs)- 38 (84) |
|
|
 |
M.6.50
TOTAL STROKE mm (inch)- 50 (1.9'')
TAPPING CAPACITY mm (inch)- MILD STEEL - M6 (1/4'')
WEIGHT - Kgs (lbs) - 15 (33)
|
|
|
 |
M.16.80-130 - M.20.80-130
TOTAL STROKE mm (inch) M.16.80 - 130 - 80 (3.15'')
TAPPING CAPACITY mm (inch)- MILD STEEL M.16.80 - 130 - m16
(1/2'')
WEIGHT - Kgs (lbs) M.16.80 - 130 - 38 (84)
|
|
|
 |
Spindle head F.25 has an ISO 30 tool
holder. It can be fitted to the slide unit by means of collar
E.FE100.
On drilling and milling (axial or radial) applications, model
F.25.RC is to be used as it is fitted with adjustable taper
roller bearings.
On boring applications, model F.25.CO is to be used as it is
fitted with a pack of three pre-loaded precision angular contact
bearings. |
|
|
 |
Spindle head F.32 is designed to be
mounted on "S" series slide units. Tool holder is ISO 30.
Different spindle bearing options are available to suit
machining applications.
On drilling and milling (axial or radial) application, model
F.32.RC is to be used as it is fitted with adjustable taper
roller bearing.
On boring application, model F.32.CO is to be used as it is
fitted with a pack of three pre-loaded precision angular contact
bearings. |
|
|
 |
Ball screw slide units S.UT.200 are
designed to carry spindle heads models "F.25 (with collar) -
F.32".
On the cast iron base rests 2 precision rails and 4 ball rows
pads and screw 25 mm dia x5 mm pitch (.98" dia x .20" pitch).
Re-circulating ball pads enable linear speeds of approximately
15 times (150 m/min- 492 FT/min) that of the one obtained on
cast iron ways, with very long lubrication intervals. High
performance with high rigidity (no traditional blocking system
is needed and eliminates oil leakage thru the guides
Thrust is supplied by a precision rolled ball screw moving
inside a no backlash pre-loaded nut assembly fitted to the
carrier.
The slide comes complete with a sealed micro-switch pack and
relative cams, normally fitted to the right hand side.
Slide units with 6 ball rows pads are supplied on request. |
|
|
 |
The hydraulic slide units S.CI. are
designed to carry spindle heads model "F.25 with collar - F.32 -
F.40".
S.CI = cast iron base with precision rails and 4 ball rows pads
Re-circulating ball pads enable linear speeds of approximately
15 times (150 m/min -492 FT/min) that of the one obtained on
cast iron ways, with very long invtervals lubrication.
Thrust is supplied by a 50 mm (1.97") bore hydraulic cylinder
fitted to the carrier.
Reccomended oil pressure is 40 bar (580 psi).
The slide comes complete with a sealed micro-switch pack and
relative cams normally fitted to the right hand side.
Stroke is set by an adjustable mechanical stop.
|
|
|
 |
The electro-hydraulic machining unit C.36
consist in a hydraulic slide, fitted with ball guides carryng an
ISO 30 cast iron body spindle head.
C.36 = F.32 (page 92) + S.CI.200 (pag.106)
The spindle is available in two different bearing configurations
which make them suitable for specific applications:
MACHINING UNIT = C.36.RC
(adjustable taper roller bearings)
This unit is especially suitable for drilling and axial or
radial milling applications.
BORING UNIT = C.36.CO
(set of three pre-loaded angular contact bearings)
This unit is especially suitable for precision
boring applications.
The unit is supplied complete with three micro switches and
adjustable cams. The switch unit is sealed and is usually fitted
on the right hand side of the slide.
Speeds 600 R.P.M. (at 50Hz) are obtained by fitting a reduction
gear ''R''.
The F.32 can be fitted to other slide units (longer strokes or
ball feed slides etc.).
|
|
|
 |
The electro-hydraulic milling unit U.F40
consists in a hydraulic slide, fitted with ball guides carryng
an ISO 40 cast iron body spindle head in vertical position.
In its standard version, the unit's configuration is:
U.F40 = F.40 (spindle assembly only - page 94) + S.TI.200 (page
108) + vertically adjustable on its support bracket.
The technical features of the unit (working stroke spindle
output-ball screw slide version) can be modified on request.
The spindle head can be set in line or side ways.
The spindle head has a fine adjustable vertical stroke for tool
setting of 50mm (1.97").
The head spindle is fitted with adjustable taper roller
bearings.
The hydraulic slide is complete with a set of 4 switches and
adjustable cams. The switch unit is sealed and is usually fitted
on the right hand side of the slide.
Spindle speeds lower than 600 R.P.M. (at 50 Hz) are obtained by
fitting a reduction gear box "R".
|
|
|
 |
Two controlled axis (Z-Y) ISO 40 milling
assembly
Z stroke = 50 mm (1.97")
Y stroke = 400 mm (15.75")
Spindle head power = 5,5 Kw
Drive = 40 mm dia x 5 (1.58" dia x .20") ball screw
Linear pads = 4 ball screw
Dedicated motor plates
Pads lubrication = centralized on axis Z and Y
Multi-switch packs on Z-Y
|
|
|
 |
The "Z" modular structure is ideal for the
manufacturing of rotary transfer machines.
The large flexibility of the system enables to display the units
supports in the required position.
At any time, it is possible to implement your machine in
expanding the number of stations by adding more units supports.
It is worth noting that even after many years of operation, your
machine can be easily and quickly converted for machining
different parts. (Also the potential trade-in value is higher
than on conventional single purpose machines).
The configuration includes:
1-Central round support in cast iron. Provision is made to fit
Euroma indexing tables models T.R.320 and T.H.350 in the center.
2-Units supports. Suitable to hold the operating units on their
mounting supports.
They can be set in any position around the central support to
which they are secured by heavy duty clamping plates to ensure
maximum rigidity.
3-Fabricated base. Standing on 4 adjustable feet.
On request can be supplied:
4-Chip and coolant apron
5-Coolant tank with pump
Electric cabinet complete according to the customer's
specification.
|
|
|
 |
Rear mounting type chucks B.AM are of the
same construction as B.AC series.This model is more satisfactory
on applications in restricted spaces.They can be either
pneumatically or hydraulically operated.
Max pneumatic operating pressure is 9 bar (131 P.S.I.).
Max hydraulic operating pressure is 20 bar (290 P.S.I.), (9
bar/131 P.S.I only on B.AM 52 and 12 bar/174 P.S.I. only on B.AM
85 and B.AM 110). Clamping force at 9, 12, 20 bar (131, 174, 290
P.S.I.) are proportional to the ones ralative to 6 bar (87
P.S.I.) as shown in the chart below.
Soft jaws can be supplied on request.
|
|
|
 |
Flange mounting type chucks B.AC are
utilized on rotary table transfer machines to firmly hold
components to be processed.
They can be either pneumatically or hydraulically operated.
Max pneumatic operating pressure is 9 bar (131 P.S.I.).
Max hydraulic operating pressure is 20 bar (290 P.S.I.), (12
bar/174 P.S.I only on B.AC 85 and B.AC 110).Clamping force at 9,
12, 20 bar(131, 174, 290 P.S.I.) are proportional to the ones
ralative to 6 bar (87 P.S.I.) as shown in the chart below.
Soft jaws can be supplied on request.
|
